When should this article be used?
Use this article when:
- The customer has a neoHub connected to an EE router by Ethernet.
- The neoHub Link light is red rather than green.
- The neoHub is showing offline in the neoApp.
- The problem started after installing or changing to a new EE router or EE broadband service.
- The Ethernet connection appears to be working, but the neoHub cannot communicate with the Heatmiser servers.
A red Link light normally means the neoHub has established a connection to the local network/router but has not successfully established its connection to the Heatmiser server.
Step 1 – Restart the neoHub
- Disconnect the power cable from the neoHub.
- Leave it disconnected for approximately 30 seconds.
- Reconnect the power.
- Allow the neoHub a few minutes to reconnect.
Check the Link light.
If the Link light turns green
The neoHub has connected successfully.
Stop troubleshooting here.
If the Link light remains red
Continue to Step 2.
Step 2 – Check the Ethernet connection
Make sure the neoHub is connected to one of the LAN ports on the EE router.
Then:
- Unplug the Ethernet cable from the neoHub and reconnect it.
- Unplug the other end from the EE router and reconnect it.
- Try a different LAN port on the EE router.
- If possible, try a different Ethernet cable.
- If the neoHub is connected through a network switch, Powerline adapter or another network device, temporarily connect it directly to the EE router.
Wait approximately one minute after each change and check the Link light.
If it remains red, continue.
Step 3 – Check that the EE router can see the neoHub
Open the EE app or EE Hub Manager and check the connected devices.
The neoHub should be listed as a connected wired/Ethernet device and should have been given an IPv4 address, normally similar to:
192.168.1.xxx
If the EE router cannot see the neoHub as a connected device, continue troubleshooting the Ethernet connection before going any further.
If the EE router can see the neoHub but its Link light remains red, continue.
Step 4 – Check EE WiFi Controls
On newer EE routers, internet access can be controlled for individual devices or groups of devices.
In the EE app, check that the neoHub:
- Has not been paused.
- Is not included in a group with internet access paused.
- Does not have an internet-access schedule applied to it.
- Is not restricted by Parental Controls.
Even though the neoHub is connected by Ethernet rather than Wi-Fi, network restrictions can still affect its internet connection.
If there are no restrictions and the Link light remains red, continue.
Step 5 – Temporarily disable Advanced Web Protect
Newer EE broadband services can use Advanced Web Protect to monitor and block network traffic that EE identifies as potentially suspicious.
As a test:
- Open the EE app.
- Go to the broadband/WiFi Controls section.
- Find Advanced Web Protect.
- Temporarily switch Advanced Web Protect OFF.
- Power cycle the neoHub.
- Allow a few minutes for it to reconnect.
If the Link light turns green
The neoHub itself and its Ethernet connection are working.
Advanced Web Protect or another EE network-security setting may be preventing communication between the neoHub and the Heatmiser servers.
The customer should contact EE Broadband Support for help allowing the neoHub's outbound traffic without disabling their network protection permanently.
If the Link light remains red
Continue.
Step 6 – Check router/network settings
The neoHub requires internet access to communicate with Heatmiser's servers.
Ask the customer or their broadband provider to confirm:
- IPv4 is available to the neoHub.
- DNS is operating correctly.
- Outbound network traffic is not being blocked.
- Ports required by the neoHub are not being restricted.
The ports to check are:
- 8000
- 2424
- 443
- 123
Important: Do not automatically instruct the customer to configure port forwarding. The neoHub initiates its connection out to the Heatmiser servers. The requirement is for the necessary outbound communication to be permitted.
If the customer is unsure how to check this, advise them to contact EE and ask EE to check whether the wired neoHub is being prevented from making outbound connections.
Step 7 – Test through a network switch
If everything above appears correct but the neoHub still shows a red Link light, there may be a compatibility or Ethernet auto-negotiation issue between the neoHub Ethernet interface and the EE router.
As a test, connect:
EE Router → Ethernet Switch → neoHub
Then restart the neoHub.
If possible, use a basic 10/100 Mbps Ethernet switch for this test.
If the Link light turns green through the switch
This suggests there may be an Ethernet negotiation compatibility issue between the EE router and neoHub rather than a problem with the Heatmiser server.
Record:
- EE router model
- EE router firmware version
- neoHub generation
- neoHub MAC address
- Whether the neoHub works when connected through the switch
Escalate this information for further investigation.
Important – Do Not Factory Reset the neoHub
Do not factory reset the neoHub as part of this troubleshooting unless specifically instructed by Heatmiser Technical Support.
A factory reset will remove the devices paired with the neoHub and can create significantly more work for the customer without resolving an EE router or internet-connectivity issue.
Information to collect before escalation
If the Link light is still red after completing the above checks, collect:
- neoHub generation
- neoHub MAC address
- Exact EE router model
- EE router firmware version, if available
- Whether the neoHub appears in the EE connected-device list
- IPv4 address assigned to the neoHub
- Whether Advanced Web Protect was enabled
- Whether disabling Advanced Web Protect changed anything
- Whether another Ethernet cable and LAN port were tested
- Whether the neoHub was tested through an Ethernet switch
- Whether the Link light is red continuously or intermittently
Then escalate for further investigation.