Use this article only when the thermostat pairing steps have been completed but the thermostat does not pair with the neoHub.
This article covers situations where:
- The Mesh symbol flashes and then disappears.
- The Wi-Fi-looking symbol flashes and then disappears.
- The wireless symbol appears during pairing but will not stay on the screen.
- The Mesh / Wi-Fi-looking symbol does not flash at all when pairing is attempted.
- The thermostat looks like it is trying to pair but does not connect to the neoHub.
- The thermostat will not pair even though the pairing steps have been followed.
This article does not cover:
- The Mesh symbol staying permanently displayed.
- Pairing a neoHub to the neoApp or phone.
- Any lights on the neoHub.
- The neoHub LINK light being red, orange or green.
- The location or property showing offline in the neoApp.
What Should Happen During Pairing?
When pairing, the Mesh symbol should flash while the thermostat is attempting to connect to the neoHub.
When the thermostat successfully connects, the Mesh symbol will stop flashing and remain permanently displayed.
There are two main failure behaviours:
- The Mesh symbol flashes and then disappears: the thermostat attempted to connect but did not successfully connect to the neoHub.
- The Mesh symbol does not flash at all: the thermostat has not entered pairing correctly or may still have previous setup/pairing information stored.
In either situation, start with a factory reset.
Part 1 - Factory Reset the Thermostat
The thermostat may still have previous pairing or setup information stored. Factory reset the thermostat before trying to pair it again.
- Use the Left / Right keys to scroll to the Power icon.
- Press and hold the Tick button until the display turns off.
- SETUP will be highlighted.
- Press and hold the Tick button for 10 seconds.
- All of the icons will appear on the display for approximately 2 seconds.
- The number 1 or 2 will then flash on the display.
- Use the Left / Right keys to select the required mode:
- Mode 1 = Thermostat
- Mode 2 = Time Clock
- Press the Tick button to confirm.
The factory reset removes the previous setup and pairing information, so the thermostat will need to be paired again.
Part 2 - Try Pairing Again
Once the factory reset has been completed, return to the neoApp and follow the thermostat pairing steps again.
Watch the Mesh / Wi-Fi-looking symbol on the thermostat.
If the symbol flashes and stays on
Pairing has been successful. No further troubleshooting is required.
If the symbol flashes and then disappears
The thermostat attempted to pair but did not establish a connection with the neoHub.
Continue to Part 3 - Check for Wireless Interference.
If the symbol does not flash at all
The thermostat has not entered the expected pairing state.
First:
- Repeat the pairing process once more.
- Make sure SETUP is selected on the thermostat.
- Confirm the pairing command on the thermostat.
- Watch the Mesh symbol carefully.
If the Mesh symbol still does not flash at all, contact Heatmiser Support for further assistance rather than continuing with the Wi-Fi interference checks.
Part 3 - Check for Wireless Interference
Only continue to this section if the Mesh symbol flashes during pairing but then disappears.
If the thermostat has been factory reset and the Mesh symbol still flashes and disappears during pairing, the next step is to check for wireless interference.
If you are currently speaking to support by telephone, ask to be transferred to an adviser who can assist further.
If you are not on a call, continue below and send the scan results to support.
If You Have an iPhone
- Download Airport Utility from the Apple App Store.
- Open your phone Settings.
- Locate Airport Utility and enable Wi-Fi Scanner.
- Open Airport Utility.
- Run a Wi-Fi scan.
- Take a screenshot of the results.
If You Have an Android Phone
- Download WiFi Analyzer (Open Source) from Google Play.
- Open the application.
- Navigate to Channel Graph.
- Make sure you are viewing the 2.4GHz graph.
- Take a screenshot of the graph.
Part 4 - Send the Results to Support
- Open your email application.
- Create a new email using the same email address registered to your Heatmiser Neo account.
- Send the email to support@heatmiser.com.
- Use the subject Devices Offline.
- Include:
- The Wi-Fi scan screenshot.
- A brief description of the problem.
- Confirmation that the thermostat has been factory reset and pairing has been tried again.
- Send the email.
What Happens Next?
The support team will review the Wi-Fi scan and check for interference between the neoHub Zigbee network and the property's 2.4GHz Wi-Fi network.
If excessive congestion or channel overlap is found, the support team can often adjust the neoHub Zigbee channel or provide further guidance to improve communication between the neoHub and the thermostat.
If the Mesh symbol never flashes
Do not send a Wi-Fi scan solely because the Mesh symbol does not flash.
If the thermostat has been factory reset, the pairing procedure has been repeated and the Mesh symbol still does not flash at all, contact Heatmiser Support for further investigation.
If it still does not work, the guidance in this article has no further steps. An adviser can help further.
Main changes: I’ve separated “flashes then disappears” from “never flashes” because they indicate different stages of failure. I’ve also made sure somebody whose symbol never flashes doesn’t unnecessarily go through the Wi-Fi scan process.