Articles in this section

How to remove a neoAir from a UH8-RF wiring centre

  • Updated
Follow

When the UH8-RF is coming on every hour when a thermostat is not paired to it.

 

If you are no longer using a zone on a UH8-RF, you will need to deactivate the zone, otherwise that zone will enter failsafe, meaning that the redundant zone will come on for 12 minutes every hour.

 

When using a neoAir V2 or neoAir V3

image.png

Using a working neoStat V2 or V3

  • Using the left and right buttons, move the box until it is over the power icon on the left.
  • Press and hold Tick until you see SETUP and CLOCK.
  • Press Tick on SETUP, then down to P2 and press Tick (make a note of the large number small number and two letters).
  • On the same screen, press tick once and change the small number to match the zone that you wish to deactivate on the UH8-RF.
  • After pressing tick a few times, it will go back to the original screen.
  • Press and hold Tick until you see SETUP and CLOCK.
  • Press Tick on SETUP, then down to P3 and press Tick.
  • Use the left arrow to make the large number 00.
  • Then press Tick.

Turn heating up and down, you should see the Zone light coming on the UH8-RF go off and on, this is sending a message to the wiring centre to unpair a thermostat previously connected to the UH8-RF on zone 1.  This will need to be done 4 times.  This will mean that the information will be transmitted on the UH8-RF to turn that zone off.

The next step is to put the thermostat back to the original settings.

Back to the thermostat

  • Go to the power icon on the left using the left button
  • Press and hold Tick until you see SETUP and CLOCK
  • Press Tick on SETUP, then down to P2 and press Tick
  • Press Tick and go to the small number, change it back to the original number, then press Tick to go back to the main screen.
  • Press and hold Tick until you see SETUP and CLOCK
  • Press Tick on SETUP, then down to P3 and press Tick
  • Use the left arrow to make the large number 01.
  • Then press Tick.

Turn the heating up and down making sure that the correct zone turns on and off on the UH8-RF

 

When using the neoStat V1

image.png

 

Using a working neoAir

  • Use the right arrow to move to SETUP on the right hand side
  • Press tick
  • Press down arrow to go to P2 and press Tick
  • Press Tick and go to the small number, change it back to the zone number you want to clear, then press Tick to go back to the main screen.
  • Using the left and right keys to go to SETUP
  • Press tick
  • Press down arrow to go to P3
  • Press tick
  • Press left arrow to make large number 00.
  • Press tick

Turn heating up and down, you should see the Zone light coming on the UH8-RF go off and on, this is sending a message to the wiring centre to unpair a thermostat previously connected to the UH8-RF on zone 1.  This will need to be done 4 times.  This will mean that the information will be transmitted on the UH8-RF to turn that zone off.

Then you need to put the neoAir back to the original settings

  • Use the right arrow to move to SETUP on the right hand side
  • Press tick
  • Press down arrow to go to P2 and press Tick
  • Press Tick and go to the small number, change it back to your original number, then press Tick to go back to the main screen.
  • Using the left and right keys to go to SETUP
  • Press tick
  • Press down arrow to go to P3
  • Press tick
  • Press right arrow to make large number 01.
  • Press tick
  • Then test by turning heating up and ensuring that the UH8-RF zone light comes on.

 

Related articles